API618_Datasheet往复式压缩机数据表

可编辑excel版

JOB NO. PURCHASE ORDER NO. DOCUMENT NO.

ITEM NO.

RECIPROCATING COMPRESSOR (API 618-4TH) DATA SHEET U.S. CUSTOMARY UNITS1 APPLICABLE TO: 2 FOR/USER 3 NOTE: 4 INDICATES INFO. TO BE COMPLETED BY PURCH. PROPOSALS SITE/LOCATION BY MANUFACTURER WITH PROPOSAL TYPE MODEL NO(S) NO. WITH CYLS. /

REVISION NO. PAGE OF

DATE BY

x

PURCHASE

AS BUILT SERVICE BY MANUFACTURER AFTER ORDER NO. REQ'D BY MANUFACTURER OR PURCHASER AS APPLICABLE SERIAL NO(S) KW @ RATED RPM OF

5 COMPR. MFGR 6 COMPR.THROWS: TOTAL NO. 7

NOMINAL FRAME RATING RPM

MAX/MIN ALLOWABLE SPEED

8 DRIVER MFGR. 9 DRIVE SYSTEM: 10 TYPE OF DRIVER: DIRECT COUPLED IND. MOTOR

DRIVER NAMEPLATE KW/OPERATING RPM GEARED & COUPLED SYN. MOTOR V-BELT GAS TURBINE ENGINE

/

STEAM TURBINE

OTHER LUBE NON-LUBE

11 NO NEGATIVE TOLERANCE APPLIES: 12 13 (NNT) MAX ACCEPTABLE AVG PISTON SPEED

YES - PURCHASER TO FILL IN "REQUIRED CAPACITY" LINES. NO - PURCHASER TO FILL IN "MFGR.'S RATED CAP." LINES m/s

CYLINDERS:

14OPERATING CONDITIONS (EACH MACHINE) 15 16 17 18 19 20 SERVICE OR ITEM NO. STAGE NORM. OR ALT. CONDITION CERTIFIED PT. (X) MARK ONE MOLECULAR WEIGHT Cp/Cv (K) @ 65° C OR ° C AT INLET TO: NOTE: PULSE DEVICES SIDE STREAM TO COMPRESSOR CYLINDER FLANGES STAGE(S), THESE INLET PRESS. ARE FIXED

21 INLET CONDITIONS: 22

23 24 25 26 27

PRESSURE (k-Bar-abs) @ PUL. SUPP. INLET PRESSURE (k-Bar-abs) @ CYL. FLANGE TEMPERATURE (° C) REF: SIDE STREAM TEMPS (° C) COMPRESSIBILITY (Zs ) INTERSTAGE D P INCL: PULSE DEVICES PIPING COOLERS SEPARATORS OTHER

28 INTERSTAGE: 29

D P BETWEEN STAGES, %/(kPa)(BAR) AT OUTLET FROM: PULSE DEVICE COMP. CYL. FLANGES OTHER

30 DISCHARGE CONDITIONS: 31 32 33 34 35

PRESSURE (k-Bar-abs) @ PUL. SUPP. INLET PRESSURE (k-Bar-abs) @ CYL. FLANGE TEMP., ADIABATIC, ° C TEMP., PREDICTED, ° C COMPRESSIBILITY (Z2 ) OR (ZAVG ) RATED FOR PROCESS, AT INLET TO COMPRESSOR, NO NEGATIVE TOLERANCE (-0%) kg/h CAPACITY SPECIFIED IS WET DRY

36 * REQUIRED CAPACITY, 37 38

39 ● m³ C) h /h (760 mm HG & 0° 40 * MFGR.'S RATED CAPACITY 41 42 43 44 45 46 47 48 49 50 INLET m³ /h m³ C) h /h (760 mm HG & 0° kW/STAGE TOTAL BkW @ COMPRESSOR SHAFT TOTAL KW INC V-BELT/GEAR LOSSES * CAPACITY FOR NNT MANUFACTURER'S = REQUIRED ÷ 0.97 THEREFORE REQUIRED = MFR'S x 0.97 REMARKS: kg/h (AT INLET TO COMPRESSSOR) & kW @ CERTIFIED TOLERANCE OF ±3% FOR CAP. & ±3% FOR kW CAPACITY SPECIFIED IS WET DRY

x